Kraber Optic Seat — Kraber 瞄具底座修正

EN — Repositions the Kraber's optics so their mounts actually sit on the picatinny rail instead of floating above it.

中文 — 修正 Kraber 三种瞄具的安装位置，让镜座真正坐在皮卡丁尼导轨上，而不是悬空。

What it changes / 修改内容

Each optic's geometry is rigidly weighted to its own bone, so the patch simply shifts those vertices along the weapon's up axis (model units).

Before / After / 修改前后

Left = original (mount floating above the rail), Right = patched.

左＝原版（镜座悬空于导轨之上），右＝修正后。

[IMAGE PLACEHOLDER] — replace with a hosted URL of preview_compare.png （图片需要上传到外部图床后把链接填到这里；Thunderstore 不渲染 zip 内的相对路径图片）

Install / 安装

EN — Unzip into your Titanfall2 folder so that the mods folder merges with Titanfall2\R2Northstar\mods. Then enable KraberOpticSeat in the Northstar mods menu (it is enabled by default when listed in enabledmods.json).

中文 — 解压到 Titanfall2 目录，让 mods 文件夹与 Titanfall2\R2Northstar\mods 合并即可。之后在北极星的模组菜单里启用 KraberOpticSeat。

Manual path / 手动路径:

Titanfall2\R2Northstar\mods\KraberOpticSeat\
    mod.json
    mod\models\weapons\at_rifle\ptpov_at_rifle.mdl

Compatibility / 兼容性

• Client-side only. Other players will not see it. It changes no damage, spread, ballistics or hit registration. 纯客户端，其他玩家看不到。不影响伤害、散布、弹道与命中判定。
• This mod replaces the entire ptpov_at_rifle.mdl. Any other mod that also replaces this file will conflict with it (whichever loads later wins). If you use a Kraber model/skin mod that ships its own .mdl, do not enable both. 本模组替换整个 ptpov_at_rifle.mdl，与任何同样替换该文件的模组冲突（后加载者生效）。如果你的 Kraber 皮肤模组自带 .mdl，不要同时启用。
• Mods that only change weapon config values (e.g. weapon-position mods that edit viewmodel_offset_ads) do not conflict at file level, but their values were tuned for the original geometry, so the aiming composition will stack. Disable them if the view looks off. 只改武器配置值的模组（例如调整 viewmodel_offset_ads 的武器位置模组）不会文件冲突，但那些数值是针对原始几何调的，同时使用时瞄准时的构图会叠加。

Notes / 备注

• The stock optic (v_scope_dcom) and the variable zoom (v_scope_talon) received very small corrections; the threat scope received the largest one.
• The Kraber's unused stabilizer optic is intentionally left untouched.
• The kill counter (Pro Screen) is not covered by this release — its display mesh is a separate model. 击杀计数器（Pro Screen）本版未包含——它的显示网格是独立模型。
• Fixing attachment seating requires moving the optic's own geometry, not just a config offset: the mount's underside is not flat, so no single viewmodel offset can make it sit flush. 修正嵌合必须动瞄具自身几何，单靠配置偏移做不到——镜座底面本身不平整。

Credits / 致谢

Model geometry is Respawn's original asset; this patch only translates part of its vertices. 模型几何为 Respawn 原始素材，本补丁仅平移了其中部分顶点。